Protective Case for RUI DENG RUIDENG RD TECH UM25C USB-Tester
Protective Case for RUI DENG RUIDENG RD TECH UM25C USB-Tester
Published 2019-09-10T09:20:17+00:00
Protective Case for RUI DENG RUIDENG RD TECH UM25C USB-Tester to cover the open boards and protect/support the USB-Ports & the switch.
MAY fit on other RUIDENG models unless some ports are not needed or different (micro-USB/USB-C) Don't know if non-Bluetooth® models will also fit in terms of overall height, but it seems so at the UM25 without "C". Only the Bluetooth® slide-switch (and the board of couse) is missing. The newest model UM34C could fit also, despite this model is lacking the USB-C Out and on the non-Bluetooth® model the switch too.
The UM24(C) model seems to be incompatible except for the overall case design. Ports & Buttons are completely different.
--------------------------------------------------------------------
Schutzhülle/Gehäuse für RUI DENG RUIDENG RD TECH UM25C USB-Tester zur Abdeckung der offenen Boards und zum Schutz/zur Unterstützung der USB-Ports und des Switches.
KÖNNTE auch auf andere RUIDENG-Modelle passen, obwohl einige Anschlüsse nicht benötigt werden oder unterschiedlich, bzw. nicht vorhanden sind (micro-USB/USB-C). Ob Modelle ohne Bluetooth® in Bezug auf die Bauhöhe auch passen, kann ich leider nicht sagen, aber es sieht beim UM25 jedenfalls so aus, da hier lediglich der Bluetooth® Schiebeschalter (und natürlich das Board) fehlen. UM34C könnte ebenfalls passen - hier hat Ruideng wohl nur den USB-C Out weggelassen. Beim UM34 Modell (also dem ohne "C" für Bluetooth®) fehlt dann auch noch der Schiebeschalter...
Das UM24(C) Modell scheint bis auf die Bauform nicht kompatibel zu sein - hier sind die Ports komplett unterschiedlich und die Knöpfe sind ebenfalls anders.
IMPORTANT: Need to resize to 10% in Slicer because SketchUp creates crappy stl on rounded/beveled surfaces at this size!!!
Supports are possibly needed for the USB-Port and Switch - infill can be as you like it. I've used 50% infill - up to 100% are fine too and make no big difference in time and material use.
Print speed was around 30mm/s to get the fine details as thight as possible. Printing time was around 1:45h for both pieces at once.
-------------------------------------------------------------------
WICHTIG: Die stl´s müssen im Slicer auf 10% verkleinert werden, da SketchUp auf abgerundeten/gefasten Oberflächen bei dieser Größe schlechte stl´s erzeugt.
Möglicherweise werden für die Aussparungen der USB-Ports und des Bloeutooth-Schalters Unterstützungen benötigt - die Füllung kann beliebig sein. Ich hab 50% Füllung verwendet - bis zu 100% sind auch in Ordnung und machen keinen großen Unterschied in Zeit und Materialeinsatz.
Die Druckgeschwindigkeit betrug ca. 30mm/s, um die feinen Details so genau wie möglich zu gestalten. Die Druckzeit lag bei ca. 1:45h für beide Teile auf einmal.
#####################################
Post-Printing
After sucessful printing remove the supports (if printed) and check all edges for overhangs, bubbles and sand them down or remove them with a exacto knife.
Testfit the lid on the base - it has to sit flush without gaps between lid & base case.
Unscrew your RUIDENG device and keep the screws separated (short for lid & long for base case)
Put in the acrylic bottom plate at first, followed by the Bluetooth® board. Eventually you have to sand down the unprecise machined edges of the circuit board (left & right at the USB Connectors) to fit in the case.
Next add the main board with display and ensure the four buttons to not catch on the edges and sit correct behind the push buttons of the case.
Cover it with the acrylic window plate and finish the sandwich by putting the lid on and ensure it sits correct.
Put the screws back in place (short for lid & long for base case) and you´re done!
-------------------------------------------------------------------
Nach erfolgreichem Druck die Supports entfernen (falls gedruckt) und alle Kanten auf Überhänge und Blasen prüfen und abschleifen oder mit einem Cutter-Messer entfernen.
Testen Sie den Deckel auf dem Unterteil - er muss bündig und ohne Spalten zwischen Deckel und Unterteil sitzen.
Schrauben Sie Ihr RUIDENG-Gerät auseinander und halten Sie die Schrauben getrennt (kurz für Deckel & lang für Basisgehäuse).
Legen Sie zuerst die Acryl-Bodenplatte in das gedruckte Gehäuse ein, dann das Bluetooth®-Board. Eventuell müssen Sie die unpräzise bearbeiteten Kanten der Leiterplatte (links & rechts an den USB-Anschlüssen) abschleifen, damit sie in das Gehäuse passen.
Als nächstes fügen Sie die Hauptplatine mit Display hinzu und achten Sie darauf, dass die vier Tasten nicht an den Kanten einrasten und korrekt hinter den Druckknöpfen des Gehäuses sitzen.
Decken Sie es mit der Acryl-Fensterplatte ab und beenden Sie das Sandwich, indem Sie den Deckel aufsetzen und sicherstellen, dass er gut und bündig sitzt.
Setzen Sie die Schrauben wieder ein (kurz für Deckel & lang für Basisgehäuse) und schon sind Sie fertig!
Date published | 10/09/2019 |
Time to do | - 105 minutes |